Cheap Chinese Powermeter

Building a cheap Chinese powermeter

I found this interesting powermeter on AliExpress.
I can't give a link because the store may change or disappear, but do a search on

RF Power Meter -75~16 dBm 1-600MHz

and you will find it for around 15€ .. including free shipping,  a real bargain !

There is not much to "build", this is not a kit but a ready-built pcb, based on an Analog Devices AD8307 logarithmic detector.
I'm pretty sure it is a clone of some known design, but could not find any more info on the internet.
Also there is no manual, but the use is very straightforward.
Just power it and it will measure ...
The external attenuation can be entered in the meter via the menu buttons, so that your reading is your actual power.

All you have to do is find a case for it.

I took a small mint tin, found two flat Li-Ion cells (from cordless telephones), a small fuse, and put it all toghether as you can see in the pictures below.

2 small Li-Ion cells 3.7V 600mAh, fit nicely in the box

A piece of PCB with cutout pads for battery and slow 250mA fuse

The only hole I had to make was for the SMA connector.

The batteries are charged with an external charger, one could of course make a simple LM317 regulator that puts a fixed 8.4V on the cells, but don't forget to put a current limiting resistor or you will blow the fuse ! ;-)

I have used a circuit like this one before with good results.
It is not a balanced charger, but with cheap cells from the junkbox I don't care too much ... from time to time I may charge cells individually with a "one cell" charger board.

And now the test .. does it work ?

Using an old HP 8640A Generator set at -20 dBm on 10 MHz, and using a 50 cm cable, the meter showed -20.3 dBm.

That's very good considering the low price of this board, and the small error can be contributed to the cable loss, or even the HP generator, which hasn't been calibrated for a long time.

Also the meter is very consistent over the whole dynamic range, down to -70 dBm, the error was never more than +/- 1dB (and supposing the attenuator in the HP generator is still accurate).

Conclusion : a very nice addition to my shack !

Now I still need a dummy load / 40 dB attenuator so I can measure all those QRP rigs I built ... Bitx40, QCX , and others ...


73
Luc - ON7DQ

Pottelberg Activation

ON/ON-027 Pottelberg

This Belgian summit is the closest one to my home in Ostend, and also my most activated summit.
It is about a 95 km drive away, and I've been there 5 times.

This is a very flat plateau, and so there are several nice spots to set up.

Driving there is also very easy, there is a cafetaria "Chalet radar", next to a football field, and lots of parking places. Position for your GPS is 50.765075, 3.699555

I did setup on the football field twice, once I went behind the field along the two transmitting towers into the woods, and twice along the track left of the cafetaria.
If you want to activate also the Fauna & Flora ONFF-0318 , the football field is not valid. The other places are.

This is the layout to use for judging if you're in the right spot for ONFF. You should setup inside the area witihin the red lines.

For this fifth activation, I used the KX3 at 15W, and my trusted 9.15m endfed on the 12m Spiderbeam pole.

Only ... I had forgotten a small detail ... my jacket !

It was a cold february afternoon, so I helped myself with a blanket from the car, and put myself in the sun ... it helped a little.
Good that I did not forget my fleece vest and orange cap, hi !

I made 44 qso's in about 2 hours and 15 minutes.
This included 4 S2S qso's, and to my surprise .. I was called by Paul, VK5PAS on 20m SSB !
That's 16000 km with only 15W ... wonderful !
Paul was 55 with me, and gave me a 53 report.
And I got a 57 from W1OW, also a respectable 5500 km away.
So propagation must have been above average that day ... and I was a lucky man !

See you on the next  one !

73

Luc, ON7DQ